1000Mbps RJ45 Gigabit Poe Outdoor Lightning Protector

Модель №.
SNH-RJ45/POE-OD

Working Voltage Un
48В

Nominal Discharge Current(8/20&Ms)in
5ka

Protection Level (8/20µs)up
100В

Protection Line
1-8

Измерение
50(H)×100(Вт)×120(L)мм

IP Level
IP65

Working Conditions
Температура: -40 к 85 Degree

Standards Compliance
Ce, FC, РоХС,ИСО9001

Adapt Transmission Rate
1000Mbps

Insertion Loss
≤0.5dB

Транспортный пакет
Carton or Wooden Cases

Технические характеристики
CE, ФКС, ИСО9001, РоХС, China National Type Test

Товарный знак
opplei

Источник
Китай

Код ТН ВЭД
8535300000

Производственная мощность
500, 000ПК/год

Описание

RJ45 1000Mbps single channel Outdoor Gigabit Power over Ethernet Surge protector

Модель: SNH-RJ45/POE-OD

1000Mbps RJ45 Gigabit Poe Outdoor Lightning Protector

1000Mbps RJ45 Gigabit Poe Outdoor Lightning Protector

APPLICATIONS:
Designed for Ethernet device in the outside not to be spoiled by lightning over-voltage, induced over-voltage and static discharge.
CAT6, CAT5e and CAT5 compatible
802.3af
10/100/1000 Base-T Gigabit Ethernet protection
LAN, FDDI,CDDI, ATM,WLAN
PDH, SDH, SPDH
Industrial control
POE IP cameras outdoor
FEATURES:
Multi. Protection circuits, Gas-Tube + TVS technology
Dual protection in Common mode and differential mode
TVS array technology, low capacitance
Multi-Strike Capability

TECHNICAL PARAMETER:
Модель SNH-RJ45/POE-OD
Electrical Parameter(Network & Власть)
Nominal operating voltage Un 48В
Максимум. continuous operating voltage Uc 60В
Nominal discharge current(8/20µs)In 3kA
Максимум. discharge current (8/20µs)Imax 5kA
Limiting voltage Up
Line-line (@6kV, 10/700µs) 150В
Line-line (@3kA, 8/20µs) 150В
Adapt transmission rate 1000Mbps
Insertion loss ≤0.5dB
Protection line 1-8
Response time 1ns
Load current 250mA
Приложение Cat. 6 one channel
Mechanical characteristics
Измерение 28(H)×87(Вт)×100(L)мм
Weight per unit 350г
Protection grade IP65
Working conditions Температура: -40 к 85С,
Relative humidity: ≤95%
Standards compliance CE, ФКС, РоХС, ИСО9001

INSTALLATION AND MAINTENANCE
а) The SPD should be connected in series between the protected device and the signal/power transmission channel.
b) The input terminal (IN) of the SPD should connect to the signal/power transmission channel, and the output terminal (OUT) of the SPD should connect to the protected device.
c) Connect earthing wire of the SPD to earthing bus-bar of the lightning protection system of the room or building.
д)No special duty needs to be carried out for maintenance. When problem arises and the SPD is suspected, check the system with SPD taken out of circuit. Should system recover, the SPD shall be regarded as a damaged unit and must be replaced immediately.

1000Mbps RJ45 Gigabit Poe Outdoor Lightning Protector
1000Mbps RJ45 Gigabit Poe Outdoor Lightning Protector

1000Mbps RJ45 Gigabit Poe Outdoor Lightning Protector