Beschrijving
| Modelnr: | ||||||||||||
| iK3AS02 | iK3AS04 | IK3AS08 | IK3AS15 | IK3AS22 | IK3AS30 | iK3AS50 | iK3BS15 | iK3BS25 | iK3BS35 | iK3BS55 | iK3BS75 | |
| 0.2kW | 0.4kW | 0.75kW | 1.5kW | 2.2kW | 3kW | 5kW | 1.8kW | 3kW | 3.8kW | 5.5kW | 7.5kW | |
| Input Power | ||||||||||||
| Control Mode | Three-phase PWM converter sine wave drive | |||||||||||
| Main Power | 220V: Single-phase/three phase 220V AC(-15~+10%,50~60Hz) | |||||||||||
| 380V: Three-phase 380V AC(-15~+10%,50~60Hz) | ||||||||||||
| Control power | 220V: Single-phase 220V AC(-15~+10%,50~60Hz) | |||||||||||
| Nominale stroom | 220V:0.2KW/2A,0.4kW/2.8A,0.75kW/5.5A,1.5kW/10A, 2.2kW/12A,3kW/16A,5kW/25A | |||||||||||
| 380V: 1.8kW/5A,3kW/8A,3.8kW/12A,5.5kW/16A, 7.5kW/20A | ||||||||||||
| Encoder feedback | ABZ incremental encoder / absolute encoder | |||||||||||
| Environment | ||||||||||||
| Werktemperatuur | 0~45°C | |||||||||||
| Storage temperature | -20~65°C | |||||||||||
| Working humidity | 20~85%RH or less (non-condensing) | |||||||||||
| Storage humidity | 20~85%RH or less (non-condensing) | |||||||||||
| Working and storage air | indoor (no direct sunlight), non-corrosive gases, flammable gases, oil mist, dust | |||||||||||
| Altitude | Below 1000m | |||||||||||
| Vibration | 5.8m/s² (0.6G) below 10~60Hz (Cannot be used continuously at resonant frequency) | |||||||||||
| Insulation and pressure resistance |
Primary- between F and G, 1 minute under AC1500V | |||||||||||
| Functions | ||||||||||||
| IO Input | 4-channel (DC24V optocoupler isolation) Input function can be selected according to parameters below: Servo on, P action, positive rotation inhibit, negtive rotation inhibit, alarm reset,positive torque limit, negtive torque limit, error clear |
|||||||||||
| IO Output | 3-channel optocoupler isolated output; the following output function can be selected according to parameters: Alarm output, position proximity, velocity consistent detection output, motor rotation detection, servo ready, torque limit, brake release |
|||||||||||
| Pulse input | Differential input: 500K; open collector: 200K Pulse + direction, AB orthogonal pulse, CW+CCW pulse |
|||||||||||
| Pulse output | Phase A, phase B: differential output. Phase Z: differential output or open collector output | |||||||||||
| Internal speed command | Three-speed distribution via input terminals | |||||||||||
| Overload Capacity | Max. 3 times torque | |||||||||||
| Analog input | 2-channel differential input ±10V, 1-channel single-ended 0-10V; switch according to control mode | |||||||||||
| Communication | Modbus; Ethercat, CANopen | |||||||||||
| Control modes | 12 control modes: position control, speed control, torque control, inner speed, position/speed control, position/torque control, speed/torque control, inner speed/position, inner speed/speed, inner speed/torque, speed/zero clamp, position control/command inhibit |
|||||||||||
| Regenerative resistance | 400W: without external regenerative resistance; over 750W: with | |||||||||||
Naming: 
Product Advantage:
Intelligent
· Powerful internal position mode allows for continuous multi-path planning for rich motion control; supports up to 32 data sets for planning, each set of data can be set to the number of pulses or angle required, and internal position mode can be set for speed, acceleration, deceleration and emergency deceleration
· Automatic determination of load inertial mechanical properties, setting optimal gain and shortening system commissioning time
Stable
· Mechanical resonance frequency analysis, configured with two sets of trap filters, adjustable frequency (50 ~ 5000Hz) and trap depth, effectively overcome low frequency resonance and mechanical end vibration, vibration frequency (1 ~ 100Hz) and vibration damping can be set
Multifunctioneel
· Frictional torque compensation reduces the effect of static friction during mechanical commutation and improves command following performance at low speeds
· Multibus support: CANopen
Easy to Operate
· Support for debugging software, mechanical characteristics analysis, parameter setting, monitoring and other functions, intuitive and simple operation
Quality management System
Each staff is required to pass the qualification test for the job position and work in strict accordance with the process documents.
A wide range of measure are applied to control quality and they are:factory audit,signing quality agreement with suppliers,incoming materials inspection,first product confirmation,inspection during production,final inspection,production process analysis and improvement,corrective and preventive actions.
Sollicitatie:
3C electronic equipment
Packaging equipment
Printing equipment
CNC Machine tools
Textile industry
Woodworking cutting machines
Bedrijf:
Laboratory:
Culture:
Award:Won the 2018 annual user satisfaction brand in the field of motion control!
Certificaat: 