1000Mbps RJ45 Gigabit Poe Outdoor Lightning Protector

מספר דגם.
SNH-RJ45/POE-OD

Working Voltage Un
48V

Nominal Discharge Current(8/20&Ms)in
5ka

Protection Level (8/20µs)up
100V

Protection Line
1-8

מֵמַד
50(H)×100(W)×120(ל)מ"מ

IP Level
IP65

Working Conditions
Temperature: -40 אֶל 85 Degree

Standards Compliance
Ce, FC, RoHS,ISO9001

Adapt Transmission Rate
1000Mbps

Insertion Loss
≤0.5dB

חבילת הובלה
Carton or Wooden Cases

מִפרָט
לִספִירַת הַנוֹצרִים, FCC, ISO9001, RoHS, China National Type Test

סִימָן מִסחָרִי
opplei

מָקוֹר
חרסינה

קוד HS
8535300000

קיבולת ייצור
500, 000PCS/שנה

תיאור

RJ45 1000Mbps single channel Outdoor Gigabit Power over Ethernet Surge protector

דֶגֶם: SNH-RJ45/POE-OD

1000Mbps RJ45 Gigabit Poe Outdoor Lightning Protector

1000Mbps RJ45 Gigabit Poe Outdoor Lightning Protector

APPLICATIONS:
Designed for Ethernet device in the outside not to be spoiled by lightning over-voltage, induced over-voltage and static discharge.
CAT6, CAT5e and CAT5 compatible
802.3af
10/100/1000 Base-T Gigabit Ethernet protection
LAN, FDDI,CDDI, ATM,WLAN
PDH, SDH, SPDH
Industrial control
POE IP cameras outdoor
FEATURES:
Multi. Protection circuits, Gas-Tube + TVS technology
Dual protection in Common mode and differential mode
TVS array technology, low capacitance
Multi-Strike Capability

TECHNICAL PARAMETER:
דֶגֶם SNH-RJ45/POE-OD
Electrical Parameter(Network & כּוֹחַ)
Nominal operating voltage Un 48V
מקסימום. continuous operating voltage Uc 60V
Nominal discharge current(8/20µs)ב 3kA
מקסימום. discharge current (8/20µs)Imax 5kA
Limiting voltage Up
Line-line (@6kV, 10/700µs) 150V
Line-line (@3kA, 8/20µs) 150V
Adapt transmission rate 1000Mbps
Insertion loss ≤0.5dB
Protection line 1-8
Response time 1ns
Load current 250mA
בַּקָשָׁה Cat. 6 one channel
Mechanical characteristics
מֵמַד 28(H)×87(W)×100(ל)מ"מ
Weight per unit 350ז
Protection grade IP65
Working conditions Temperature: -40 אֶל 85ºC,
Relative humidity: ≤95%
Standards compliance לִספִירַת הַנוֹצרִים, FCC, RoHS, ISO9001

INSTALLATION AND MAINTENANCE
a) The SPD should be connected in series between the protected device and the signal/power transmission channel.
b) The input terminal (IN) of the SPD should connect to the signal/power transmission channel, and the output terminal (OUT) of the SPD should connect to the protected device.
c) Connect earthing wire of the SPD to earthing bus-bar of the lightning protection system of the room or building.
d)No special duty needs to be carried out for maintenance. When problem arises and the SPD is suspected, check the system with SPD taken out of circuit. Should system recover, the SPD shall be regarded as a damaged unit and must be replaced immediately.

1000Mbps RJ45 Gigabit Poe Outdoor Lightning Protector
1000Mbps RJ45 Gigabit Poe Outdoor Lightning Protector

1000Mbps RJ45 Gigabit Poe Outdoor Lightning Protector