1000Mbps RJ45 Gigabit Poe Outdoor Lightning Protector

N º de Modelo.
SNH-RJ45/POE-OD

Working Voltage Un
48V

Nominal Discharge Current(8/20&Ms)in
5ka

Protection Level (8/20µs)up
100V

Protection Line
1-8

Dimensión
50(H)×100(W)×120(L)milímetro

IP Level
IP65

Working Conditions
Temperatura: -40 para 85 Degree

Standards Compliance
Esta, FC, RoHS,ISO 9001

Adapt Transmission Rate
1000Mbps

Insertion Loss
≤0.5dB

Paquete de transporte
Carton or Wooden Cases

Especificación
ESTA, FCC, ISO 9001, RoHS, China National Type Test

Marca comercial
opplei

Origen
China

Código hs
8535300000

Capacidad de producción
500, 000PC/Año

Descripción

RJ45 1000Mbps single channel Outdoor Gigabit Power over Ethernet Surge protector

Modelo: SNH-RJ45/POE-OD

1000Mbps RJ45 Gigabit Poe Outdoor Lightning Protector

1000Mbps RJ45 Gigabit Poe Outdoor Lightning Protector

APPLICATIONS:
Designed for Ethernet device in the outside not to be spoiled by lightning over-voltage, induced over-voltage and static discharge.
CAT6, CAT5e and CAT5 compatible
802.3af
10/100/1000 Base-T Gigabit Ethernet protection
LAN, FDDI,CDDI, ATM,WLAN
PDH, SDH, SPDH
Industrial control
POE IP cameras outdoor
FEATURES:
Multi. Protection circuits, Gas-Tube + TVS technology
Dual protection in Common mode and differential mode
TVS array technology, low capacitance
Multi-Strike Capability

TECHNICAL PARAMETER:
Modelo SNH-RJ45/POE-OD
Electrical Parameter(Network & Fuerza)
Nominal operating voltage Un 48V
máx.. continuous operating voltage Uc 60V
Nominal discharge current(8/20µs)En 3kA
máx.. discharge current (8/20µs)Imax 5kA
Limiting voltage Up
Line-line (@6kV, 10/700µs) 150V
Line-line (@3kA, 8/20µs) 150V
Adapt transmission rate 1000Mbps
Insertion loss ≤0.5dB
Protection line 1-8
Tiempo de respuesta 1ns
Load current 250mamá
Solicitud Cat. 6 one channel
Mechanical characteristics
Dimensión 28(H)×87(W)×100(L)milímetro
Weight per unit 350gramo
Protection grade IP65
Working conditions Temperatura: -40 para 85ºC,
Relative humidity: ≤95%
Standards compliance ESTA, FCC, RoHS, ISO 9001

INSTALLATION AND MAINTENANCE
a) The SPD should be connected in series between the protected device and the signal/power transmission channel.
b) The input terminal (IN) of the SPD should connect to the signal/power transmission channel, and the output terminal (OUT) of the SPD should connect to the protected device.
c) Connect earthing wire of the SPD to earthing bus-bar of the lightning protection system of the room or building.
d)No special duty needs to be carried out for maintenance. When problem arises and the SPD is suspected, check the system with SPD taken out of circuit. Should system recover, the SPD shall be regarded as a damaged unit and must be replaced immediately.

1000Mbps RJ45 Gigabit Poe Outdoor Lightning Protector
1000Mbps RJ45 Gigabit Poe Outdoor Lightning Protector

1000Mbps RJ45 Gigabit Poe Outdoor Lightning Protector